Forum Replies Created
|
RE: Cirrus Dart???? Keep in mind that while the TRA world records cannot be set with motors that have fallen out of cert, the NCR club records most certainly can. I have 2 AT F32's and 5 G55's... and there ain't nothing ... |
In forum Archives 2006-2010 |
18 years ago |
|
Off until the 27th Folks, I'm gone until the 27th and will NOT have access to email or the web. If you have any problems related to the website, please feel free to drop me a line and I'll get to it as soon as I return.... |
In forum Archive - News & Events |
18 years ago |
|
RE: Cirrus Dart???? I have a 4" MD project being built around the CTI M795 motor - the current record motor - that's pretty close to optimal. I'll be tweaking it and planning on flying it either at NCR later this summer ... |
In forum Archives 2006-2010 |
18 years ago |
|
RE: Cirrus Dart???? For true altitude records birds - not going after the low hanging fruit - you definitely need to go apogee deploy only. No question but that the inches you save in airframe length will definitely grab... |
In forum Archives 2006-2010 |
18 years ago |
|
RE: Cirrus Dart???? I've done min diameter birds from 18mm up through 54mm so far. My preference is to work with FWFG (filament wound fiber glass), but that's purely a labor convenience. On 29mm and 38mm you can definite... |
In forum Archives 2006-2010 |
18 years ago |
|
RE: Cirrus Dart???? The next O project is going to be minimum diameter... hehe 😯 |
In forum Archives 2006-2010 |
18 years ago |
|
RE: Motors for the Aerotech 29/360 casing It seems that dividing records by impulse range is the only truly logical solution. John and I have had a fair amount of discussion about altitude records over the last few years and one piece of fall... |
In forum AP Motor Discussion - Certified |
18 years ago |
|
RE: Loki K350 hardware? I have the full kit including a reload. I plan on flying it in June or July in my 4" bird - you're welcome to use it afterwards. W |
In forum Knowledge Base |
18 years ago |
|
RE: Thrust ring question If it's any help, I'd buy a few if you end up having to have them made. Warren |
In forum Knowledge Base |
18 years ago |
|
RE: Thrust ring question John, the split rings used by Skyripper hybrids are somewhat less than half the exposure of the AMW rings - also a bit lighter and thinner. I don't know where they get theirs but that would be where I... |
In forum Knowledge Base |
18 years ago |
|
RE: Writer's Cramp Well done Joe... take a bow and have a beer - you deserve it. Warren |
In forum Archives 2006-2010 |
18 years ago |
|
RE: Two-Stage - Sustainer Fin can 54mm motor MIA --> FOUND! That has to be the most Challenger-like post mortem video I've ever seen in rocketry. Excellent Mike. Warren |
In forum Lost and Found |
18 years ago |
|
RE: Launch Event Volunteers - new topic name That's EXACTLY it! - We need to plan for next time and we need to start looking at next time...right now! Excellent thoughts Joe. Warren |
In forum Archive - News & Events |
18 years ago |
|
RE: Launch Event Volunteers - new topic name A few years ago I got it in my head that NCR was such a great club with such a great launch site that we should host LDRS. I brought it up at one of my first Executive Committee meetings and was shot ... |
In forum Archive - News & Events |
18 years ago |
|
RE: Lost: top half of Quest Penetrator MHM Sat. It was at the launch table Sunday morning. Either Joe has it or it is in the trailer. W |
In forum Lost and Found |
18 years ago |