Forum Replies Created
|
RE: Need help on launch lug sizing However, not on 3 G's It has to have one motor in the cluster at least that is in the certifying class. So an H and 2 G's would be OK, but not 3 G's. |
In forum Construction Help |
20 years ago |
|
RE: Need help on launch lug sizing Another (much cheaper) option than the first fires are Quickburst. Unfortunately, they are gone until the first of may, so so may have to eat the cost of the first fires for Mayhem, and then go to the... |
In forum Construction Help |
20 years ago |
|
RE: Need help on launch lug sizing yeah - those are motor casings. John (I assume) was asking about reloads. Also, good luck with mile hi mayhem, and trust me, you'll be hooked 🙂 Someday, you'll think of G's as the motor you launch whe... |
In forum Construction Help |
20 years ago |
|
RE: Hot loads I'll put one in my BBX sometime, oktoberfest at the latest Should make the 12lb rocket leap off the pad quite nicely... |
In forum AP Motor Discussion - Certified |
20 years ago |
|
RE: Need help on launch lug sizing Why would they have K's? Did Joe finally secure a LEDP? |
In forum Construction Help |
20 years ago |
|
RE: Hot loads Hmmm... Just got some other info on this - looks like they are the: J1423N-P (54/852) J2135N-P (54/1280) and another H....H669N-P (38/240) |
In forum AP Motor Discussion - Certified |
20 years ago |
|
RE: Hot loads Yep. Also, I heard that AT is almost done with their green formula, although they haven't announced anything, so that should be nice when it arrives. From what I've heard, it is a laser green that bur... |
In forum AP Motor Discussion - Certified |
20 years ago |
|
RE: Hot loads Yeah, and if they're about this, I can't wait to hear them |
In forum AP Motor Discussion - Certified |
20 years ago |
|
RE: Hot loads I don't doubt it, as Gary has hinted about an upcoming load that will be announced in a few days. However, I do need details 🙂 What case(s) would this(these) be for? I would LOVE a 54/1280 warp 9 8) |
In forum AP Motor Discussion - Certified |
20 years ago |
|
RE: Hot loads I didn't hear anything of this - where did this come from? However, there are some neat pics of the H999, as well as a vid. Pic 1 Pic 2vid |
In forum AP Motor Discussion - Certified |
20 years ago |
|
RE: Need help on launch lug sizing Theoretically, a 3/8 or 1/2 inch lug would be fine. Realitically, throw the lugs away and switch to rails. They whip less, are easy to use, and the buttons add less drag and impact the appearance a lo... |
In forum Construction Help |
20 years ago |
|
RE: Single Shot Sweepstakes 2006 Warren - side bet (gentleman's bet - I'm poor right now from Mayhem 🙁 ) THe winner will be >6k |
In forum Contests |
20 years ago |
|
RE: Single Shot Sweepstakes 2006 😆 I've done it. Once 8) It's a pain, but I'll do it for this contest |
In forum Contests |
20 years ago |
|
RE: Single Shot Sweepstakes 2006 The current club altitude record for the G motor is 6383' and is held by John Wilke. The Tripoli world G record is 7567' and is held by William Inman. I would expect altitudes in the high 5000's to be... |
In forum Contests |
20 years ago |
|
RE: Single Shot Sweepstakes 2006 Warren, from your delay... I am so doomed. 🙂 Agreed. I only need 14.8 |
In forum Contests |
20 years ago |